Skip to content
OffroadTips logo — light bar icon with the OffroadTips wordmark
  • Home
  • About UsExpand
    • Contact Us
  • Light Bars
  • Pod Lights
  • Light Wiring
  • Free Tools
  • UTV Lighting
  • Light Mounts
OffroadTips logo — light bar icon with the OffroadTips wordmark
Free calculator

Cordless LED Work Light Runtime Calculator

Estimate how long a cordless LED work light runs on a tool battery from volts, Ah and watts, with a 2, 4, 5 and 9 Ah pack comparison.

  • Free
  • No sign-up
  • Runs in your browser
Estimates only · data checked October 2026 · About this data

Estimate only. Real runtime depends on brightness mode, temperature, battery age and the light's own electronics. The 85% efficiency is an adjustable assumption, not a measured value for any product, and the tool does not check whether a light is compatible with a battery.

Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.

Quick answer

To estimate runtime for an LED work light for a Milwaukee 18V battery, multiply the pack’s volts by its amp-hours, apply an efficiency factor, and divide by the light’s watts. Enter those below for an instant estimate in hours and minutes. This tool checks energy only, not whether a light fits a battery.

How to use the runtime calculator

  1. Choose your battery platform. The presets set the voltage only: Milwaukee M18 (18 V), DEWALT 20V MAX (calculated at its 18 V nominal voltage), Generic 12 V, or Custom if your pack has a different voltage.
  2. Enter the pack capacity in amp-hours (Ah), or tap a 2, 4, 5 or 9 Ah quick-pick button. The capacity is printed on the battery.
  3. Enter the light’s power in watts (W). Use the watt rating on the light or in its spec sheet, not the lumens.
  4. Leave efficiency at 85% or change it. The result updates as you type, and the “Show the maths” line lets you check every step by hand.

Below the headline runtime you get a comparison table for 2, 4, 5 and 9 Ah packs at the same voltage, watts and efficiency. If your own capacity matches one of those sizes, that row is marked “your pack”. Nothing you type is stored or sent anywhere; the calculation runs in your browser.

How the runtime calculation works

Battery energy is voltage multiplied by capacity: amp-hours times volts gives watt-hours. The calculator then applies an efficiency percentage to get the energy you can actually use, and divides by the power the light draws.

  1. Battery energy (Wh) = voltage (V) × capacity (Ah)
  2. Usable energy (Wh) = battery energy × (efficiency % ÷ 100)
  3. Runtime (hours) = usable energy ÷ light wattage (W)
  4. Minutes = round(runtime hours × 60), halves rounded up, shown as “X h Y min”

Worked examples at 18 V, a 20 W light and 85% efficiency, using the example pack sizes in the calculator:

PackBattery energyUsable energy (85%)Runtime (hours)Runtime
2 Ah36 Wh30.6 Wh1.53 h1 h 32 min
4 Ah72 Wh61.2 Wh3.06 h3 h 4 min
5 Ah90 Wh76.5 Wh3.825 h3 h 50 min
9 Ah162 Wh137.7 Wh6.885 h6 h 53 min

These are hypothetical inputs to show the method, not runtimes for any named product. Set efficiency to 100% and the result becomes exactly watt-hours divided by watts: 18 V × 5 Ah = 90 Wh, and a 20 W light gives 4.5 h, or 4 h 30 min.

Why efficiency is editable. The 85% default is this tool’s own adjustable assumption. It is not a standard, and it is not a measured or typical value for any light or battery. If a manufacturer publishes a runtime for your exact light and pack, prefer that figure and use this calculator for what-if comparisons.

Milwaukee M18, DEWALT 20V MAX and rechargeable magnetic work lights

People usually shop for an LED work light for a Milwaukee 18V battery, or an LED work light for a DEWALT battery, by the tool platform they already own. The voltage presets cover that starting point. Milwaukee lists its M18 REDLITHIUM XC5.0 pack (48-11-1850) as an 18-volt, 5.0 Ah battery, so the M18 preset uses 18 V.

DEWALT’s “20V MAX” label needs a footnote. On its DCB205 5Ah battery page, DEWALT states that the maximum initial battery voltage, measured without a workload, is 20 volts, and that the nominal voltage is 18. A nominal figure is the right one for an energy estimate, so the DEWALT preset calculates with 18 V and the tool shows that footnote whenever the preset is selected.

The same maths applies to a rechargeable magnetic work light with a built-in battery. Enter its battery voltage and Ah (if the spec sheet lists them) with the light’s watts, or choose Custom for an uncommon voltage. If the spec sheet gives only watt-hours, divide by the light’s watts and multiply by your efficiency assumption.

The presets never claim which light fits which battery. Check fit and compatibility on the manufacturer’s own product page before you buy.

Where to find your light’s wattage

Look for a watt (W) figure on the label, the housing, the box or the spec sheet. Lumens describe how much light comes out, not how much power goes in, so they cannot go in the wattage field. If a light has several brightness modes, enter the wattage for the mode you will actually use, or run the calculator once per mode.

Limits of this estimate

Converting amp-hours to watt-hours through a single voltage is approximate. As the Wikipedia article on the kilowatt-hour puts it, the value is approximate because the battery voltage is not constant during its discharge, and because higher discharge rates reduce the total amount of energy that the battery can provide. Brightness mode, temperature, battery age and the light’s own electronics also move the real number. Treat the result as a planning estimate, and leave a margin if you depend on the light.

Methodology & sources

The formula is a basic physical relationship (watt-hours equal volts times amp-hours), applied exactly as written above. The only numbers the tool supplies itself are the 85% default efficiency (an editable assumption) and the 2, 4, 5 and 9 Ah table sizes (example sizes). Brand names appear only on the voltage presets, and only the 5 Ah packs listed below were checked against a manufacturer page. Prices, lumens and light wattages are deliberately left out.

  • Wikipedia: Ampere-hour (Ah × V = Wh; accessed October 2026)
  • Wikipedia: Kilowatt-hour, Related units (why the conversion is approximate; accessed October 2026)
  • DEWALT DCB205 20V MAX 5Ah battery product page (20 V maximum initial voltage, 18 V nominal, 5 Ah; accessed October 2026)
  • Milwaukee Tool M18 REDLITHIUM XC5.0 battery, 48-11-1850 (18-volt, 5.0 Ah; accessed October 2026)

Last updated: October 2026

FAQ

How long will an LED work light run on a Milwaukee 18V battery?

Multiply 18 V by the pack’s Ah to get watt-hours, multiply by the efficiency you assume, then divide by the light’s watts. For example, 18 V × 5 Ah = 90 Wh; at 85% that is 76.5 Wh, and a 20 W light would run about 3 h 50 min.

Is a DEWALT 20V MAX battery 18 V or 20 V in the calculation?

The calculator uses 18 V. DEWALT states that the maximum initial battery voltage, measured without a workload, is 20 volts and that the nominal voltage is 18.

Why is efficiency set to 85%?

It is an editable assumption of this tool, not a measured or typical value for any light or battery. Set it to 100% to get the plain watt-hours divided by watts figure.

Does this calculator tell me which lights fit my battery?

No. It only does the energy math, so check fit and compatibility on the manufacturer’s own product page.

Should I enter lumens or watts?

Enter watts. The formula divides stored energy by the power the light draws, and lumens describe light output rather than power.

Related guides

  • LED Light Bar Maintenance Checklist: Seasonal Care for Longer Life
  • 12 Best LED Cube Lights for UTVs
  • What Makes a Quality LED Light Bar? The Specs That Actually Matter
  • What Beam Pattern Is Best for Ditch Lights? Flood vs Wide vs Spot
  • Can You Drive With Off-Road Lights On? On-Road vs Trail Rules
  • Fog Lights vs Driving Lights: Beam Shape, Purpose and Legal Use

More free tools

LED Light Bar & Whip Light Remote Control App Finder

Filter 24 verified iOS and Android apps that control LED light bars, whip lights, rock lights and underglow by brand, light type and features.

Off-Road Lighting Amp Draw & Wire Gauge Calculator

Find how many amps your LED light bar, pods and rock lights draw on 12 V or 24 V, then check wire gauge and voltage drop for your run.

Spot vs Flood Beam Width Calculator

Enter two beam angles from a spec sheet and compare how wide each beam is at 50, 100, 200 ft or a custom distance.

See all free tools (4) →

  • Home
  • About Us
  • Contact Us
  • HTML SITEMAP
  • Privacy Policy
  • Terms of Service
  • Affiliate Disclaimer
  • How We Research

Please keep in mind that we may receive commissions when you click our links and make purchases. However, this does not sway our reviews and comparisons. We try our best to keep things unbiased, in order to help you make the best choice. As Amazon Associate, we earn from qualifying purchases.

© 2026 OffroadTips | All Rights Reserved.

Scroll to top
  • Home
  • About Us
    • Contact Us
  • Light Bars
  • Pod Lights
  • Light Wiring
  • Free Tools
  • UTV Lighting
  • Light Mounts
Search